Avenue 4.5 and Arena 5
To start using the Advanced Output, select the Output > Advanced menu option.
You will see a window that lists the active screens on your computer down the left hand side.
Each screen represents an output going out of Resolume.
To setup a screen, right click on it on the left hand side. You will see a dropdown of all outputs that are connected to your computer. You can choose which output this screen should use. This way you can very quickly assign the correct screen to the correct output when working with multiple outputs.
The screen will show the output it's sending to under its name, as well as in the Device dropdown menu on the right. You can also change the name of a screen by double clicking on it.
Any monitors or projectors connected to your computer are automatically available as output for screens. Resolume will show the name and resolution of this connection.
Keep in mind that Resolume itself does not create outputs. This is handled by your computer itself. So if you have a screen connected to your computer, but it doesn't appear here, you will first need to make sure your computer recognizes it correctly. Check if it's set to proper extended desktop mode (PC) and the arrangment is not set to mirrored (Mac). You can read all about setting up extended displays in the chapter on Simple Output.
Every output can only have a single screen associated with it. The poor projector would otherwise get very confused when you try to send it two whole frames of pixels on every frame. When you select an output already in use by another screen, Resolume will set the output of the other screen back to virtual.
Tip! If you accidentally select the main monitor as your output, the output will fill the main monitor and you won't be able to access the interface anymore. Don't worry! Just hit CTRL-SHIFT-D ( CMD-SHIFT-D on Mac ) to disable all outputs and get the interface back.
Also cards that have both an input and an output can be used for output. Keep in mind that not all cards support full duplex ( simultaneous input and output ).
Output via playback cards is only available in Resolume Arena.
Syphon ( Mac ) or Spout ( PC ) are protocols for texture sharing between applications. They will let the output of one application magically appear as an input in another application running on the same computer. Check out the Syphon / Spout chapter in the manual for more info on Syphon and Spout,
When enabled, Resolume will always send out the main composition output. You can share additional outputs via the Advanced Output.
Resolume will use the name you give the screen as the Server Name / Sender Name. By default this would be 'Screen 1'. You can change it to whatever you like. We recommend the name 'Charlie Screen'. This screen has one speed: Go!
On the Mac, it will use either 'Avenue' or 'Arena' as the application name. On the PC, the application is called either 'Resolume Avenue' or 'Resolume Arena'
You can change the width and height of the screen to change the resolution of the texture you want to share.
Virtual Outputs are sort of an internal Syphon/Spout, just for Resolume. Screens set to virtual outputs can be picked as input for slices in other screens.
This allows all sorts of complex scaling and routing possibilities, with no extra performance hit.
You can change the output resolution of a Virtual Output by changing its width and height.
Each screen has Opacity, Brightness and Contrast controls, as well as individual controls for the Red, Green and Blue channels. You can use these to adjust mismatched outputs. For instance, you can dim the brightness on a LED panel while sending the undimmed output to a projector as well. Or you can remove some red from a projector when it doesn't match the other projectors you are using.
Each screen can have a delay between 0 and 100 ms, to account for small delays introduced by the signal chain after the outputs leave Resolume.
You can temporarily turn a screen off and on by clicking the toggle in front of it. This will enable or disable all output to that screen. This is very useful when identifying which screen is which during troubleshooting or to temporarily disable a single screen during performance.
You can also fold and unfold a screen by clicking the arrow beneath it. This will keep the output going, while hiding all the slices contained in the screen. This is useful to prevent slices from getting in the way when working with lots of screens and slices.
You can prepare your screens without having them physically connected. This is useful when you need to prepare for a show before the venue is open.
When you open the Advanced Output without having any secondary screens connected, it will open with a single Virtual Screen. You can set the resolution of this Virtual Screen using the Width and Height parameters on the right hand side.
By matching these settings to the resolution that your output will have during show, you can prepare your setup beforehand. Then, once you are connected to the actual output, you can tell your screen to use that output instead, via the right-click dropdown.
You can create as many Virtual Screens as you need via the Plus+ menu.
Do you want to use Resolume with more outputs than your computer has ports for? Check out our handy MultiScreen PDF that walks you through the various options.