Search found 2481 matches

by Oaktown
Thu Aug 22, 2019 03:58
Forum: Problems? Bugs? Solutions!
Topic: Blackmagic Decklink and Resolume Arena 16:10 Aspect Ratio?
Replies: 2
Views: 57

Re: Blackmagic Decklink and Resolume Arena 16:10 Aspect Ratio?

16:10 is a computer resolution and Blackmagic only does SMPTE resolutions so it’s not possible to output 16:10 with a Decklink card.
by Oaktown
Sat Jun 29, 2019 15:50
Forum: Problems? Bugs? Solutions!
Topic: dmx preferences
Replies: 3
Views: 212

Re: dmx preferences

raybuay@hotmail.com, I'm assuming you want to create DMX universes for output not input, correct? If that's the case, you need create the Lumiverses in the advanced output not in the preference menu.

https://resolume.com/support/en/dmx
by Oaktown
Sat Jun 29, 2019 14:55
Forum: Problems? Bugs? Solutions!
Topic: Arena, Quadro P4000 and Bluefish444 Supernova 4K
Replies: 12
Views: 327

Re: Arena, Quadro P4000 and Bluefish444 Supernova 4K

Can you try converting your mp4 file to DXV3 to see if that might be part of the issue?
by Oaktown
Sat May 11, 2019 15:09
Forum: Hardware
Topic: Using Matrox GPU to create 8 outputs
Replies: 1
Views: 355

Re: Using Matrox GPU to create 8 outputs

Not sure what type of projectors (HD?) you’re using but my recommendation would be to use a RTX 2080 card with 2 Datapath FX4
by Oaktown
Fri Feb 22, 2019 19:12
Forum: Problems? Bugs? Solutions!
Topic: Blend mode on bypassed layer
Replies: 3
Views: 354

Re: Blend mode on bypassed layer

If you don't have content in the layer, what are you trying to blend?
by Oaktown
Fri Feb 22, 2019 18:25
Forum: General Chat
Topic: Artnet to DMX software
Replies: 3
Views: 486

Re: Artnet to DMX software

You're welcome and it should be an easy one to create!
by Oaktown
Fri Feb 22, 2019 09:03
Forum: General Chat
Topic: Artnet to DMX software
Replies: 3
Views: 486

Re: Artnet to DMX software

Create a simple network in TouchDesigner that receives Artnet (DMX In CHOP) and outputs it via a USB interface (DMX Out CHOP)
by Oaktown
Tue Feb 12, 2019 03:00
Forum: Problems? Bugs? Solutions!
Topic: Flip Composition Output Horizontally For Rear Projection
Replies: 13
Views: 3643

Re: Flip Composition Output Horizontally For Rear Projection

You know Resolume better than me, but when you use the pacmans, I think the blends end up on the two sides of the comp instead of in the center. Right? Correct, which is why you want to swap your two slices after you've flipped them so that essentially you're looking at your blend from behind (rear...
by Oaktown
Mon Feb 11, 2019 15:40
Forum: Problems? Bugs? Solutions!
Topic: Flip Composition Output Horizontally For Rear Projection
Replies: 13
Views: 3643

Re: Flip Composition Output Horizontally For Rear Projection

Oaktown: I had tried what you suggested, but that is what resulted in the soft edge blend flipping with the slice. The soft edge was then at the outer edge of the slice, rather than on center where it overlaps the other slice. All you need after you flip the screen is to swap your slices in the adv...
by Oaktown
Mon Feb 11, 2019 08:21
Forum: Problems? Bugs? Solutions!
Topic: Flip Composition Output Horizontally For Rear Projection
Replies: 13
Views: 3643

Re: Flip Composition Output Horizontally For Rear Projection

Just flip your output in the advanced output and switch your inputs.

phpBB [video]