Search found 2485 matches

by Oaktown
Fri Feb 22, 2019 09:03
Forum: General Chat
Topic: Artnet to DMX software
Replies: 3
Views: 538

Re: Artnet to DMX software

Create a simple network in TouchDesigner that receives Artnet (DMX In CHOP) and outputs it via a USB interface (DMX Out CHOP)
by Oaktown
Tue Feb 12, 2019 03:00
Forum: Problems? Bugs? Solutions!
Topic: Flip Composition Output Horizontally For Rear Projection
Replies: 13
Views: 3711

Re: Flip Composition Output Horizontally For Rear Projection

You know Resolume better than me, but when you use the pacmans, I think the blends end up on the two sides of the comp instead of in the center. Right? Correct, which is why you want to swap your two slices after you've flipped them so that essentially you're looking at your blend from behind (rear...
by Oaktown
Mon Feb 11, 2019 15:40
Forum: Problems? Bugs? Solutions!
Topic: Flip Composition Output Horizontally For Rear Projection
Replies: 13
Views: 3711

Re: Flip Composition Output Horizontally For Rear Projection

Oaktown: I had tried what you suggested, but that is what resulted in the soft edge blend flipping with the slice. The soft edge was then at the outer edge of the slice, rather than on center where it overlaps the other slice. All you need after you flip the screen is to swap your slices in the adv...
by Oaktown
Mon Feb 11, 2019 08:21
Forum: Problems? Bugs? Solutions!
Topic: Flip Composition Output Horizontally For Rear Projection
Replies: 13
Views: 3711

Re: Flip Composition Output Horizontally For Rear Projection

Just flip your output in the advanced output and switch your inputs.

phpBB [video]
by Oaktown
Tue Feb 05, 2019 16:18
Forum: New Features
Topic: Longer transitiontimes
Replies: 2
Views: 8702

Re: Longer transitiontimes

Take a look at this short tutorial as it might help you out:

phpBB [video]
by Oaktown
Wed Jan 23, 2019 09:12
Forum: Problems? Bugs? Solutions!
Topic: Projector Warping / Stacking Help (Best Practice)
Replies: 3
Views: 741

Re: Projector Warping / Stacking Help (Best Practice)

Is this what you’re after:
phpBB [video]
by Oaktown
Wed Jan 23, 2019 09:07
Forum: General Chat
Topic: Control Settings - 1 Key Reset to Start position
Replies: 4
Views: 2776

Re: Control Settings - 1 Key Reset to Start position

Reopen the saved file
by Oaktown
Mon Jan 21, 2019 16:14
Forum: Problems? Bugs? Solutions!
Topic: Resolume Artnet I/O
Replies: 3
Views: 835

Re: Resolume Artnet I/O

Laptop --> Gigabit switch MA (Artnet 1) --> Gigiabit switch Led Strips (Artnet 2-22) --> Gigiabit switch Keep in mind that an Art-Net subnet starts at 0 and only has 16 universes (0-15) so to span 22 universes, you'll need to two subnets (0 and 1). That means your incoming signal from the GrandMA w...
by Oaktown
Mon Jan 21, 2019 16:03
Forum: New Features
Topic: Ability to change advanced output presets without going into menu.
Replies: 11
Views: 7605

Re: Ability to change advanced output presets without going into menu.

... but I'm curious about what HTP merging is. Could you describe how it works? Top HTP merging would mean that you combine 2 DMX signals and the Highest value Takes Precedence. Typical merging options would be Highest value Takes Precedence, Lowest Takes Precedence, Latest Takes Precedence, and Ba...
by Oaktown
Sun Jan 13, 2019 15:20
Forum: Hardware
Topic: Resulume arena with BlackMagic Decklink 4k Extreme 12G
Replies: 5
Views: 4240

Re: Resulume arena with BlackMagic Decklink 4k Extreme 12G

Would running a Blackmagic card as the primary GPU perform better with syncing signal across outputs?
A capture card is not a GPU so that won’t work.