Tearing issue

Post your questions here and we'll all try to help.
Post Reply
bedoe
Met Resolume in a bar the other day
Posts: 5
Joined: Sun Nov 05, 2017 19:17
Location: Jakarta

Tearing issue

Post by bedoe » Wed Aug 08, 2018 10:24

hi everyone,

Sorry for my poor english

I have throuble with tearing betwen output..

My setup:
Macpro late 2013
3.5GHz 6-Core Intel Xeon E5 processor
16GB 1866MHz DDR3 ECC memory
Dual AMD FirePro D500 with 3GB GDDR5 VRAM each
Storage 256 SSD

Connected with Barco Encore2 using 2 MDP to DP cable.
Resolution 3840x1080 each output.

The problem came up with resolume 6, but it doesn't show at resolume 5.

If you guys have any solution, please share to this forum.

Sincerly,
Bedoe

Recorded video:
Tearing resolume 6:
https://youtu.be/G3BC9Kmsjxc

No tearing resolume 5:
https://youtu.be/iU4OtwvB6-I
Attachments
Resolume 6
Resolume 6
Resolume 5
Resolume 5

User avatar
francoe
Is seriously in love with Resolume. Met the parents and everything
Posts: 317
Joined: Thu Nov 27, 2008 23:30

Re: Tearing issue

Post by francoe » Fri Aug 10, 2018 05:11

I think that's not an issue to be fixed, as you asked on update announcement.
Do you tryed to change your composition fps?

Zoltán
Team Resolume
Posts: 3757
Joined: Thu Jan 09, 2014 13:08
Location: Székesfehérvár, Hungary

Re: Tearing issue

Post by Zoltán » Fri Aug 10, 2018 12:14

If this is a constant delay between outputs you see, you could try to add a frame delay to the Screen that is outputting before the other. https://resolume.com/support/en/screens#adjusting-delay
Theatre sound engineer, photographer, programmer, aka ravensc.
Control Your show with ”Enter” - multiple Resolume servers at once - SMPTE/MTC column launch
try for free: http://programs.palffyzoltan.hu
VJ footage: https://goo.gl/58oHy7

bedoe
Met Resolume in a bar the other day
Posts: 5
Joined: Sun Nov 05, 2017 19:17
Location: Jakarta

Re: Tearing issue

Post by bedoe » Fri Aug 10, 2018 12:21

francoe wrote:
Fri Aug 10, 2018 05:11
I think that's not an issue to be fixed, as you asked on update announcement.
Do you tryed to change your composition fps?
I havent try that.. I'll try and make a report..

bedoe
Met Resolume in a bar the other day
Posts: 5
Joined: Sun Nov 05, 2017 19:17
Location: Jakarta

Re: Tearing issue

Post by bedoe » Fri Aug 10, 2018 12:24

Zoltán wrote:
Fri Aug 10, 2018 12:14
If this is a constant delay between outputs you see, you could try to add a frame delay to the Screen that is outputting before the other. https://resolume.com/support/en/screens#adjusting-delay
It's not constant, delay only happen when show fast animation.. in slow video, it looks fine..

Zoltán
Team Resolume
Posts: 3757
Joined: Thu Jan 09, 2014 13:08
Location: Székesfehérvár, Hungary

Re: Tearing issue

Post by Zoltán » Fri Aug 10, 2018 13:05

bedoe wrote:
Fri Aug 10, 2018 12:24
It's not constant, delay only happen when show fast animation.. in slow video, it looks fine..
You probably don't see it in a slow animation, because the difference between the frames is so low.
Theatre sound engineer, photographer, programmer, aka ravensc.
Control Your show with ”Enter” - multiple Resolume servers at once - SMPTE/MTC column launch
try for free: http://programs.palffyzoltan.hu
VJ footage: https://goo.gl/58oHy7

bedoe
Met Resolume in a bar the other day
Posts: 5
Joined: Sun Nov 05, 2017 19:17
Location: Jakarta

Re: Tearing issue

Post by bedoe » Wed Aug 15, 2018 07:15

Problem solved

Thanks for francoe, i usually set the FPS composition to Auto, on this case, we need to adjust FPS comp.. minimum 30fps, if lower than that you'll see some Lag on video...

ranvier
Met Resolume in a bar the other day
Posts: 9
Joined: Thu Aug 11, 2016 13:24

Re: Tearing issue

Post by ranvier » Wed Aug 22, 2018 09:26

As far as i can remember from various responses from different technical discussions elsewhere, Mac Pro multiple outputs are not in sync with each other.

Apple built a custom AMD Radeon graphic driver without the eyeinfinity feature.

Thus you can't sync up the outputs from the graphic card system level

Post Reply